Skip to Content

Drawer Dividers DIY: How to Make Durable Dividers for a Bedroom Dresser

Some people dive into deep cleaning every spring, but for me, spring fever hits as an irrepressible urge to organize! Since the weather began to turn here in the Ozarks, I’ve de-cluttered 2 closets, most of my kitchen cabinets, my bedroom dresser, and half of my especially-disheveled garage.

Adding dividers to my drawers was at the top of my list for this spring, but I had to get creative about my method. Searches for DIY drawer dividers on Pinterest and Google brought up lots of cardboard and foam craft-board solutions, but in a dresser that was bought by my grandfather during the great depression, in a house that’s stood for almost 90 years, I knew a flimsy fix using craft-grade supplies would quickly look shabby- and didn’t seem appropriate.

How to use builder grade foam sheets to create durable DIY drawer dividers

As I planned these DIY dividers, I acknowledged upfront that I always overstuff organizers and dividers to their capacity and beyond. Given this, I knew from experience that it’s best to invest in appropriately sturdy materials.

The following section may contain affiliate links. As an Amazon Associate, we earn from qualifying purchases.

Off on my search I went and quickly found a much sturdier, easy to craft with material:   Commerical Polystyrene Insulated Sheet – aka “Foam Core Board” – but not the sort of foam core board you find at craft stores. This building-construction grade material is MUCH stronger, thicker, and more rigid than craft store foam boards, for about the same price per square foot.  I like this product because it’s rigid, lightweight, easy to cut, and priced well for DIY drawer dividers.  The advantage of this material over foam is that it will never “crumble” as it ages like styrofoam is prone to do.

Pre-Building: Planning my DIY Dresser Drawer Dividers

Before cutting up my foam, I took measurements of my drawers and plotted how large I wanted each compartment. I picked 5in x 5in for my sock and underwear drawer, and 7×7 for my bra/shapewear drawer.  Remember, when plotting your drawer dividers to factor in the thickness of the boards.

Step by step instructions for making dresser drawer dividers

Materials Needed:

STEP 1: CUT “BOARDS” FROM YOUR FOAM SHEET:

My drawers are 8 inches deep, so I planned for 6″ high dividers. I used a ruler and a straight edge to cut my large 4ft x 8ft board into 6″ wide strips, then cut the strips to the lengths required to accommodate the dimensions of my drawer.

Use a ruler to mark where to make your cut:

measuring for DIY drawer dividers
I marked along the length of my foam board at the 5 7/8″ measurement.

Place a straight edge (like a ruler or board) along your measurement marks and use the knife to deeply score a straight cut in the foam board:

scoring foam board for dividers
A board used as a straight edge helps keep the cut absolutely straight

It’s easy to make clean, straight cuts on this material, just use a box cutter to carefully create a deep score across the top of the board, then, with even pressure, bend away from the cut side and the board will break cleanly where the score was made.

creating the dresser drawer dividers

The waterproofed version of these boards sold for insulation will have a plastic film on the outside. Because the material is coated with a polyurethane, you’ll have to use your blade to cut through the film holding the broken pieces together:

DIY dresser drawer dividers made from this foam board require careful cutting

Continue cutting until your boards are the length needed for your drawers.

Step 2.  Cut Notches for Building Grid

While gluing pieces together is an option, creating notches and fitting the boards together is fairly quick and creates a much stronger joint.

To build a grid, use a scrap piece of foam to mark the placement and width of your notches before cutting:

Marking the cuts for DIY drawer divider foam

You’ll need to use your knife to cut through the full thickness of the material this time- so be sure and work on a surface that is durable and not sensitive to scratches!

cutting notches for a homemade drawer divider grid
Cutting notches in three layers at once

Step 3: Painting your Dividers

Once you have your pieces cut, assemble the drawer dividers and make sure the pieces fit together as you planned. Then, make sure the assembled divider fits in your drawer. If you desire a finished look, you’ll now want to paint or cover the foam. I chose to paint my first set- and watched with horror as the first paint I tried caused the surface of the board to bubble and deform!

Thankfully, switching to a really high quality surface primer resolved this issue.  Zinsser Bulls Eye 1-2-3 Primer/Sealer, came to the rescue with a great finish with no bubbling underneath. I added a topcoat of grey to match my drawers.

Painting your homemade Drawer Dividers -Hawk-Hill.com

The painted grey pieces, ready to have edges finished:

How to Make Durable Drawer Dividers for Pennies: Hawk-Hill.com

Step 4: Finishing Edges of your Drawer Dividers

If your notches turned out perfect and the exposed edge of the foam boards don’t bother you, you can stop here. I chose to go just a bit farther and cover each of my edges and seams with duct tape. This hid the exposed edges and any gaps in how my drawer dividers fit together- and added quite a bit of sturdiness. For my underwear drawer, I chose zebra tape on grey, and for my shapewear drawer, I finished the boards with white paint and used white duct tape for a very plain look.

I’m not sure how well the duct tape will wear over the years, but if it begins to look worn I may try spray-adhesive to apply a non-fraying fabric like fleece or knit cotton to my foam dividers for a softer look and feel.

How to Make these lightweight Drawer Dividers for Pennies: Hawk-Hill.com

White tape on white boards:

Zebra tape on grey boards:

 Lingere Drawer with dividers in Vintage Dresser

To finish, first apply duct tape to each and every joint, covering any gaps and smoothing the joints. Trim excess at the bottom:

trim tape from the dividers

Next, apply tape to the top edges, cutting the tape as shown to accommodate joints and allow the tape to lay flat:

Carefully cover the top edge of the dividers- this is the part you'll see most often!

Continue until all the edges and joints that will be exposed when installed are covered.

Cover joints in the foam

You can leave the outside edges uncovered, since they’ll butt up against the drawer’s sides:

These divers work great in vintage dressers because you can build a custom size partition

And that’s it!

I’m thrilled with how this project turned out and, may I admit, installing dividers was the first time in my life that I began actually folding my underwear? they just seem so cheerful folded and tucked into cubbies sorted by favorite to least favorite.

UPDATE 11/2019

It’s been a few years since I wrote this post, but these dividers have held up really well to daily use. In the time since I made them, I’ve had the opportunity to experiment with more materials on various projects, and through that, I think I have a solution for an issue I had with these dividers:

Using tape to cover the edges is playful, but doesn’t create a smooth, professional look, which I’d prefer. I’d considered spray painting over the tape, but knew from experience paint won’t stay adhered to duct tape.

When working on horse head shaped wreaths over the last fear years, I started using Plasti-Dip Spray – which sprays on to creates a smooth texture and adheres really well to everything I’ve tried. Unfortunately, I’ve sold this dresser so I can’t give it a go, but if I was to recreate this project I would add a final step of coating the entire thing in white spray-on plasti-dip coating instead of duct tape, for a polished, seam-joined, finish.

How to Make Durable Drawer Dividers for Pennies: Hawk-Hill.com
Vintage Chest of Drawers in Grey Bedroom: Hawk-Hill.com

If you liked my tutorial on soft foam DIY-built dresser drawer dividers, check out my tutorial on creating cheap wood dividers for kitchen drawers, jewelry drawers or, like this top drawer of my dresser, handkerchief/scarf drawers!

Vintage dresser Grey Bedroom with handkerchief drawer: Hawk-Hill.com

If you liked this, you might like my tutorial on lining drawers with felt for a non-slip, luxury interior:

How to use builder grade foam sheets to create durable DIY drawer dividers

Thanks for Reading!!!

I hope you can tell that I love DIY, researching the best affordable solutions for every-day problems opportunities and documenting / sharing solutions!🙌 Hawk-Hill.com is reader-supported.

☕ Hawk-Hill.com is reader-supported. If this article saved you time or money, please consider donating $1 to help me cover the cost of hosting this website OR If you appreciate this information and want to throw a “Thanks!” my way by buying me a coffee – I would Of Course appreciate it! :]

Reader Questions and Recommendations

Readers, do you have any favorite topics / posts? What would you like to read more about in the future? As I hope you can tell from this and other articles on my site, I really enjoy DIY / a good challenge, and I’m not afraid to roll up my sleeves to figure out a great, and hopefully simple 😁 solution. So please feel free to let me know in the comments below (or reach out via social media)!

Ok Really – I’ll try to wrap this up now😂

Finally, if you’d like to continue to learn about interesting DIY options as well as how YOU can tackle creative new projects consider checking out the latest and most popular articles listed on the Hawk-Hill Home Page. I’m always trying to enjoy and write about the creative side of life so please don’t be a stranger – check back often!😍

If you enjoyed this post you may also enjoy reading / perusing / devouring😊 one or all of these articles as well!

Judy

Sunday 27th of January 2019

I love this. I've been wracking my brain over what I could use for dividers for clear plastic bins to store items. This looks perfect. I'm off to the big box store to buy some foam core board. Brilliant! Thanks so much for this tutorial. So appreciated.

Patricia Jenkins

Monday 7th of December 2015

I love this ideal it just seem very complicated